V2 ENAMEL Acrylic Urethane Paint

V2 Enamel Urethane Paint was designed for use in high production, quick turn around in shed and furniture manufacturing. It works great for exterior and interior applications and is also an excellent choice for exterior fiberglass and metal entrance doors, overhead doors, trim and decorative painting. It is non-hazardous, almost odorless and easily cleans up with water.

V2 Enamel Urethane Paint is fast drying and easy spraying with unique self leveling technology.

For use on primed siding, wood, metal, fiberglass and PVC.

Click Image to Enlarge

available in 1QT, 1GAL, 5GAL & 55GAL drum.

Application Instructions

Temperature
The ideal room and product temperature is between 60- 80 degrees. Warmer room air temperatures may cause the coating to dry too quickly at the edges of the spray fan causing a dusty over spray. Cooler temperatures will slow drying times. The NaturalKote V2 Enamel temperature should be similar to the room temperature for best results. Substrate temperature should be consistent with the room and coating temperature. The siding must be dry and free of dirt or dust. Consistent temperatures of the spray room, coating and substrate are important for the proper application of NaturalKote V2 Enamel.

Equipment
Spray equipment must be maintained and working properly for best results. We recommend using a 415 or 417 tip. Equipment recommendations are general and can vary with the personal preferences and requirements of each person doing the application. We recommend that those doing the application experiment with different tips and find what works best for your situation and circumstances.

Application
Stir/Mix thoroughly before using. For semi-transparent look apply one coat on pre-primed surfaces. For solid look apply two coats. We recommend two coats on previously unpainted surfaces. Allow the first coat to dry before applying a second coat. We recommend priming bare metal with a rust inhibiting primer then apply two coats of NaturalKote V2 Enamel. Begin by making sure your sprayer pressure is correct. Spray a test panel and lower the sprayer pressure until there are fluid streaks at the outside edge of the spray fan. Gradually increase the pressure until the streaks go away. Make a note of the pressure for future reference.

Different sprayers may require different pressures so be sure to test a new or different sprayer before spraying a barn.

Apply the first coat with even, up and down strokes holding the spray fan in the center of each groove in the siding. Fan width and coating volume may vary a little depending on your tip and equipment but with the recommended tip sizes there should be very little difference. Wait until the first coat has dried enough to be just a little tacky and apply the second coat. Apply the second coat a little heavier than the first by going a little bit slower.

Ventilation
Ventilation of the spray room is critical for timely drying of the NaturalKote V2 Enamel. The spraying process of this waterborne coating creates moisture in the air that needs to be ventilated out of the room for quicker drying. Air movement needs to be through and out of the spray room, not just around the spray room. The best way to do this is to have a fresh air intake of some kind, even if it’s a window or door, and exhaust fans at the other end of the room blowing air to the outside. The more moisture you move out of the spray room with ventilation the quicker the coating will dry. The less air you move through the longer it will take to dry. Humid and colder air will slow drying times.

Product type: Waterbased Urethane/Acrylic

Spread Rate . . . . . . . .350 – 450
% (NVM) . . . . . . . . . . . . .28 – 29
VOC’s . . . . . . . . . . . . . <50 (G/L)
UV Resistance . . . . . . . . . Pass
Mold & Mildew
Resistance . . . . . . . . . . . . Pass

Dry time:
to touch. . . . . . . . . . 30 minutes
to handle. . . . . . . . . 60 minutes
to topcoat. . . . . . . . . 30 minutes
to cured. . . . . . . . . .. . . . 7 days